装修与电气

本文着重地论述了由装修而引发的电气安全技术问题已到了不容忽视的程度。就此问题作 者提出了自己的观点及解决办法。     

CVT起步离合器模糊控制算法研究

探讨了汽车无级变速器控制的关键技术之一———汽车起步离合器的控制技术,并针对汽车起步时条件的多样性以及驾驶员意图的不确定性,研究了适用于复杂条件的模糊控制算法.在离合器的滑磨阶段,把动态跟踪发动机转速的油压作为控制目标,离合器结合的控制便转化为一闭环控制.结果表明汽车能在任意工况下平顺快速起步.因此,本研究为控制CVT(Continuously Variable Transmission)起步离合器这种时变、非线性系统提出了一种简单可行的解决方法.     

双板差分冲量式谷物流量传感器设

设计了一种双板冲量式谷物流量传感器及其差分消振电路,以消除车身振动对测产精度的影响.振动试验表明,在没有谷物输入时联合收获机车身振动导致前后2个检测板产生的2个振动信号是一对共模信号,可通过电路差分的方法消除;差分后传感器的输出电压的信噪比由2.5dB提高到62dB.在零喂入量情况下,振动产生的零点误差小于0.01g/s;在联合收获机正常作业的喂入量范围内(0.5～2kg/s),实验室测量误差小于3%.田间实际测量误差不大于5%.     

中小型水电站发电机专用断路器的选择

正确设计选择发电机保护断路器直接关系到水电站后期的电气设备合理投资、运行维护及保证水电站长周期安全经济地运行.过去中小型水轮发电机大都选用普通型的油断路器或真空断路器或SF6断路器等,近些年来选用普通真空断路器的越来越多.中小型水电站应根据不同接线方式、不同容量的发电机出口断路方法,选择发电机专用断路器.     

基于LabVIEW的红枣干燥机控制系统的设计

为了解决现有红枣干燥机自动化程度低、劳动强度高和不能很好地满足红枣干燥工艺需要的问题,通过对国内外自动化控制系统的研究和借鉴,设计了基于LabVIEW的红枣干燥机的控制系统。同时,设计了LabVIEW控制系统的前面板和程序框图,完成了外部硬件电路的设计。试验表明:该LabVIEW控制系统可以实现鼓风机和物料提升机的启动和停止,3路温度的采集、分析、显示和对加热管的控制,3路湿度的采集、分析、显示和对排湿阀门的控制,2路风速的采集和显示,以及6个进/出风通道按照设定的时间间隔实现5种工作模式的切换。     

试验条件对标准橡胶塑性初值和保持率的影响与分析

通过测试不同厚度的试样和改变相同厚度试样的老化时间及温度来验证和分析试样厚度对塑性初值（P0）、老化条件对塑性保持率（PRI）的影响。试验表明,在其它试验条件不变的情况下,试样厚度偏大塑性初值（P0）也相应偏大,老化时间越长和老化温度越高,老化后的P30和塑性保持率（PRI）就越小。     

云南佤族文化旅游资源开发

分析了佤族的司岗里文化、猎头风俗以及其他独特文化的旅游资源价值,认为长期以来佤族旅游由于交通不便、开发意识不足、宣传力度不够等原因使这些资源处于沉睡状态。因此,在旅游需求、通达条件、国家西部大开发深度都已发生深刻变化的今天,主张抓好相关设施建设,做好宣传工作,不仅将大力促进这些地方旅游业发展,还将为广大旅游消费者提供高品质的旅游商品。     

Quantification of reservoir bags as airway pressure-limiting devices in a nonrebreathing system

ObjectiveTo evaluate the influence of reservoir bag types, volumes and previous use on the peak pressures (Pmax) and the times to develop 30 cmH₂O pressure (P30) within a nonrebreathing system with a closed adjustable pressure-limiting (APL) valve.Study designIn vitro study using three-way factorial design with repeated measure on one factor.SubjectsA total of 75 new anesthesia reservoir bags (five types, three volumes, five bags from each type × volume). The bag types were reusable latex (RL), disposable latex (DL) and three disposable neoprene (DN-1, DN-2 and DN-3).MethodsEach bag was tested three times (treatments): new, after prestretching and 1 week later. The bags were attached to a Bain system and anesthesia machine with closed APL valve and patient port with O₂ flow 2 L minute^–1 until Pmax was reached. The Pmax and time to reach P30 values were determined from recorded pressure traces. General linear mixed model analysis was used to examine the effects of bag type, volume and treatment. One-sided 95% upper prediction limits of Pmax were calculated to test the null hypothesis that predicted Pmax of new bags would be ≥ 50 cmH₂O for each factor combination.ResultsRL bags were the least and DN-3 bags were the most compliant. Prestretching increased compliance in all bag types. Smaller bags of RL, DL and DN-1 were less compliant than larger ones. The predicted Pmax values were < 50 cmH₂O only for DN-3 bags after prestretching. The time to reach P30 was critically low when using 0.5 L bags (median 17 seconds).Conclusions and clinical relevanceTo minimize the risk of barotrauma, highly compliant reservoir bags (e.g. DN-3) are recommended and reusable bags should be avoided. Bags should be prestretched before first use, 0.5 L bags should be avoided and fresh gas flow minimized.     

泵站继电保护设计方法

分析了进口、国产继电保护设备的不同，提出了对泵站继电保护二次回路的设计新方法。泵站二次设计可按照“单元”设置的原则，将泵站二次设计划分为10／6kV泵站进线、主机、站变、所变、联络等主要单元。     

CMOS集成块在水电站控制电路中的应用

在水电站控制电路中,为完成全站逻辑选控开停机,逻辑选控同期合油开关、跳油开关的功能,用CMOS集成电路替代分立元件,从而提高了水电站的自动化程度,缩小了集控台体积,也有利于安装、调试和维修。